| 加入收藏 | 聯系我們
產品分類
當前位置:首頁 - 新聞動態-公司新聞
新聞動態
聯系我們
濟南fun88乐天堂有限公司
地址:濟南市歷城區工業北路161-1號fun88乐天堂
電話:0531-88771456
手機:13698644688
郵箱:371162023@qq.com
傳真:0531-80992585
聯系人:萬經理
輸紙吸嘴的調整應注意的一些問題?
作者:admin 來源:本站 發布時間:2019-6-1 14:31:00 瀏覽次數:148
輸紙吸嘴在印刷中十分的重要,因為他影響著印刷的效率問題,我們在印刷前應該對其進行一些調整,使其達到良好的工作狀態。下面濟南彩色乐天堂fun88体育就給大家總結一下輸紙吸嘴的調整應注意的一些問題,希望對大家有所幫助!
Paper feeding suction nozzle is very important in printing because it affects the efficiency of printing. We should make some adjustments before printing to make it work well. The following Jinan color design printing to summarize the adjustment of paper feeding suction nozzle should pay attention to some problems, I hope to help you!
分紙吸嘴的風量盡量要小,可以換印刷薄紙用的小孔狀皮圈。另外,壓紙鋼片也要換薄的那一種。
The air volume of the separator suction nozzle should be as small as possible, and the small hole-shaped leather ring for printing thin paper can be replaced. In addition, the paper-pressed steel sheet should be replaced by the thin one.
(1)分紙吸嘴位置要進步,以剛好能吸起一張紙為宜,能調理壓紙腳上下的則恰當調高壓紙角,以增加分紙吸嘴與紙張的間隔。
(1) Paper separating suction nozzle position should be improved to just suck up a piece of paper, and adjust the high-pressure corner of paper foot to increase the distance between paper separating suction nozzle and paper.
(2)壓紙腳與壓紙鋼片要恰當增加壓紙長度,在規范壓紙長度的狀況下多壓1mm。
(2) Press foot and steel sheet should increase the length of press paper properly and press 1 mm more under the condition of standard press length.
(3)紙垛離擋紙舌的位置要比規范狀況低一些,以減少紙張往前竄的可能性。
(3) Paper stack is less positioned away from the tongue than the standard condition, so as to reduce the possibility of paper moving forward.
(4)松紙吹嘴與壓紙吹嘴的吹風量一定要小,避免吹亂紙張,使能剛好吹起5~10張紙為宜。

(4) The blowing volume of loose paper blowing nozzle and press paper blowing nozzle must be small. It is advisable to avoid disturbing the paper so that it can blow just 5-10 sheets of paper.

濟南彩色乐天堂fun88体育

(5)分紙吸嘴要恰當傾斜,使分紙吸嘴的平面與紙張平行,減少紙張破口現象的發作。
(5) Paper splitting suction nozzle should be properly tilted so that the plane of the paper splitting suction nozzle is parallel to the paper, so as to reduce the occurrence of paper breakage.
(6)遞紙吸嘴恰當進步高度,以回程時皮圈不蹭到紙張為宜。
(6) Paper delivery suction nozzle should be properly advanced so that the leather ring should not rub against the paper during the return journey.
(7)側吹風量要小,吹嘴位置要低,以紙張剛好疏松為宜。
(7) The side blowing volume should be small and the position of the blowing nozzle should be low, so the paper should be just loose.
(8)叼口處兩側的吹風量要恰當加大一點,以吹起20張紙左右為宜,避免因擋紙舌阻撓紙角而形成紙張出褶。
(8) The amount of air blowing on both sides of the mouth should be increased appropriately. It is advisable to blow about 20 sheets of paper to avoid the folding of paper caused by the blocking tongue obstructing the corner of the paper.
(9)及時清算叼口處的紙灰,以免影響光控靈活度,招致機器無故停機。
(9) Clear the paper ash at the mouth in time, so as not to affect the flexibility of light control and cause the machine to stop without reason.
以上的精彩內容由濟南彩色乐天堂fun88体育廠家友情提供,更多的精彩內容請繼續關注我們:http://fashionalized.com,我們會有更多的精彩內容等你查看!
The above wonderful content is provided by Jinan color design and printing factory friendship. More wonderful content please continue to pay attention to us: http://fashionalized.com, we will have more wonderful content waiting for you to see!