| 加入收藏 | 聯系我們
產品分類
當前位置:首頁 - 新聞動態-公司新聞
新聞動態
聯系我們
濟南fun88乐天堂有限公司
地址:濟南市歷城區工業北路161-1號fun88乐天堂
電話:0531-88771456
手機:13698644688
郵箱:371162023@qq.com
傳真:0531-80992585
聯系人:萬經理
印刷不上墨的問題你經歷過嗎?
作者:admin 來源:本站 發布時間:2019-5-7 14:08:16 瀏覽次數:199
提到印刷不上墨,應該是每個印刷廠都會遇到的問題。操作人員關于不上墨的態度普通就是“沒有方法了,就這樣用吧。”當然是在概率比擬低的狀況下。假如頻率比擬高,印不出活件,影響開機產量了,那就倡議換機臺印刷。當時看似“處理了問題”,但是過一陣子問題又頻繁發作。所以今天濟南宣傳單頁印刷廠家要來討論一下不上墨問題的成因和處理辦法。
When it comes to printing without ink, it should be a problem that every printing factory will encounter. Operator's attitude about not being able to ink is usually "no way, just use it." Of course, in the case of low probability. If the frequency is comparable to high, and no movable parts can be printed, which affects the start-up output, then it is advisable to change the printing table. At that time, it seemed to have "dealt with the problem", but after a while, the problem recurred frequently. So today Jinan Publicity sheet printing manufacturers want to discuss the causes and solutions of the problem of not ink.
1.開機就發作不上墨
1. Turn on and you won't get ink.
假如剛上機就發作不上墨,處置辦法可用潔版劑來擦拭,假如擦拭后就沒有問題了,這個屬于浮臟惹起,普通和印刷沒有關系。
If you can't get ink on the computer, the disposal method can be wiped with detergent. If there is no problem after wiping, it belongs to floating dirt, which has nothing to do with printing.
成因:浮臟,檢查沖版機水洗和上膠局部,如水洗毛刷能否有凝膠,由于環保壓力下,很多客戶曾經把水洗改成自循環,為了避免發臭,常常會參加添加劑,一朝一夕便會有贓物混入版面,另外檢查維護膠能否有按正常的比例,普通重新清洗水槽,改換維護膠便可處理。

Causes: floating dirty, check the washing machine and glue parts of punching machine, such as whether the brush can be gelled, because many customers have changed the water wash into self circulation under the pressure of environmental protection. In order to avoid stinking, they often participate in the additives. Overnight, there will be stolen goods mixed into the layout. In addition, check whether the maintenance glue can be kept in normal proportion, clean the sink again, and change the maintenance glue. Handle.

濟南宣傳單頁印刷產品

2.印刷到中途呈現毛病
2. Faults in printing
開端還比擬正常,但是中途就逐步發現某一個顏色變淺,查看印張和版材,印張上面特別是在實地塊的邊緣局部,發作相似掉網的磨損。但是用潔版液擦拭版面后發現藥膜層還是存在的。這個時分就需求查看不上墨的位置,判別能否屬于咬口或者版尾由于機械壓力不均,磨損毀壞了藥膜的砂目,招致砂目無法支撐足夠的油墨的粒子,從而形成油墨無法傳送。但是假如整個版面都存在,且無規律可循,那么就需求檢查潤版液的參數或者品牌能否會和油墨及版材發作“不匹配”。由于油墨的黏性和流變性,水斗液的張力控制都會影響到版面的水墨均衡。由于版面的親墨層還在,闡明是屬于有非親墨的物質附著上面了,普通用潔版劑擦拭后,可暫時印刷幾百張,但是不久后又開端發作。倡議更好還是徹底清洗水箱,清潔水墨路,重新分配水箱參數,是能夠處理的。
At the beginning, it is comparable to normal, but in the middle, it is gradually found that a certain color becomes lighter. Look at the printed sheet and plate, especially at the edge of the real block, there is similar wear and tear. But after wiping the plate with the cleaning solution, it was found that the film still existed. At this time, it is not necessary to check the position of the ink, to determine whether it belongs to the bite or the end of the plate due to uneven mechanical pressure, wear and tear the sand of the film, resulting in sand can not support enough ink particles, thus forming ink can not be transmitted. But if the entire layout exists and there is no rule to follow, then it is necessary to check whether the parameters of the embellishment solution or the brand will "mismatch" with the ink and plate. Because of the viscosity and rheology of the ink, the tension control of the bucket fluid will affect the ink balance of the layout. Since the ink-affinity layer of the layout is still there, it is clarified that it belongs to the non-ink-affinity material attached to it. After wiping with a general detergent, hundreds of copies can be printed temporarily, but soon it starts to break out again. It is advisable to thoroughly clean the water tank, clean the ink circuit and redistribute the parameters of the water tank, which can be handled.
以上是以毛病發作的時間來查找問題所在,那么假如時間是不定時的發作,機臺和所用資料之間也沒有明顯的規律,還是時不時的一宗毛病,可能這才是實踐印刷消費中遇到的問題。
Above is to find out the problem by the time of the occurrence of the problem, then if the time is an irregular occurrence, there is no obvious law between the machine and the data used, or a fault from time to time, this may be the problem encountered in the practice of printing consumption.
其實經過以上剖析能夠理解到,“不上墨”并不是難以處理的問題,主要是先分分明不上墨發作的時間段和找出資料匹配方面的規律,問題自然迎刃而解,而標準地控制好印刷各個環節可能呈現的問題就至關重要了。
In fact, through the above analysis, we can understand that "no ink" is not a difficult problem to deal with. It is mainly to clarify the time period of no ink onset and find out the law of data matching. The problem will be solved naturally, and it is crucial to control the problems that may appear in all links of printing.
以上的精彩內容由濟南宣傳單頁印刷廠家整理提供,希望對大家有所幫助!更多精彩內容歡迎關注我們的官網:http://fashionalized.com
The above wonderful content is provided by Jinan Publicity Page Printer. I hope it will be helpful to you all. Welcome to our website: http://fashionalized.com